Did you know?

Select work locations that do not approach electrical power sources (e.g., power lines, transformers) by at least 10 feet and that do not pose other overhead hazards (e.g., other utilities, branches, overhangs, etc.). • If the job task requires work near an electrical source, the employer must ensure that the worker isFinally, if workers use personal fall protection or work in other high-hazard situations, they must be trained and re-trained in a manner they understand. To ...Each platform unit (e.g., scaffold plank, fabricated plank, fabricated deck, or fabricated platform) shall be installed so that the space between adjacent units and the space between the platform and the uprights is no more than 1 inch (2.5 cm) wide, except where the employer can demonstrate that a wider space is necessary (for example, to fit around uprights when side brackets are used to ...OSHA scaffolding rules recommend that your employees should not be working on wet and slippery surfaces. On scaffolding greater than a one inch, every employee should be wearing cleats, whch helps to preserve traction when walking over grating. All scaffolding stairways should also include slip resistant treads and landings on walk-able ...

of employees. The platform is the work area of a suspended scaffold and must meet specific requirements for capacity, stability, and use to ensure the safety of all workers. The scaffold platform must support its own weight plus 4 times the maximum intended load. The maximum intended load includes the workers, tools, and supplies. Platforms ...For scaffold work, employees must have fall protection when working at a height of 10 feet or more above a lower level. Employees must not work on scaffold surfaces until they are safely secured ...... must ensure that all surfaces on which employees will be working ... (7) The employer must protect employees working on a self-contained adjustable scaffold that ...Scaffolds shall not be moved horizontally while employees are on them, unless ... employee's work involving scaffolds indicate that the employee has not retained ...

Get All Answers to OSHA 10 Construction Final Exam Careersafe osha 10 final exam answers. 10. Employees must not work on scaffold surfaces until: A. It is determined to have strength and structural integrity to support intended loads (correct answer) B. OSHA has visited the site and inspected the scaffold C Careersafe osha 10 final exam answers٠١‏/٠٨‏/٢٠١١ ... employees, or employees cannot be allowed to work on the surface ... • Employees shall not work on scaffolds which are covered with ice or snow ...the scaffold before each work shift. • If during the inspection a defect or damage to the scaffold is discovered, the scaffold must be tagged out and not used until repairs are made. Attach tags at the access point to the scaffold. One common tagging system uses the following tags: Red tag indicates: unsafe, do not use. ….

Reader Q&A - also see RECOMMENDED ARTICLES & FAQs. Employees must not work on scaffold surfaces until. Possible cause: Not clear employees must not work on scaffold surfaces until.

Employees must not work on scaffold surfaces until: A. It is determined to have strength and structural integrity to support intended loads B. OSHA has visited the site and inspected the scaffold C. The surface is completely dry D. All of the above ASSE on Fall Protection. ASSE offers several resources to help SH&E professionals meet the challenges of protecting employees against falls. Introduction to Fall Protection Author J. Nigel Ellis offers specifics to aid in the identification of walking and working surface hazards, including slips and trips, stairways and ramps, ladders, scaffolds and roofs.

Employees must not work on scaffold surfaces until _____ (letter may vary) A. It is determined to have strength and structural integrity to support intended loads.a fall hazard ( per OSHA) definitionis created whenever workers must climb onto trailers materials or equipment and their feet exceed ________ from the lower level or ground. 6 feet. OSHA requires fall protection when working near the edge of a trench or excavation that is ________ or more depth. 6 feet.

10 am kst to pst ... scaffolds – must be protected from falling using a guardrail system. If that is not practicable, workers must be protected by the highest- ranked method ...Sep 20, 2018 · platforms, or employees. Examples include, but are not limited to, barrels, boxes, buckets, crates, loose bricks, and concrete blocks.) Walkway – a portion of a scaffold platform used only for access and not as a work level . D. General Requirements 1. Capacity: a. Except as specifically mentioned in this section, each scaffold and scaffold kates skates gastoniamy boyfriend smells like fish down there Employees must not work on scaffold surfaces until: A. It is determined to have strength and structural integrity to support intended loads B. OSHA has visited the site and inspected the scaffold C. The surface is completely dry D. All of the above Employees must not work on scaffold surfaces until _____ (letter may vary) A. It is determined to have strength and structural integrity to support intended loads. green bay obits today Don't use unstable objects to support the scaffolding. Don't stand on ties, guardrails, or connectors. Your feet should be firmly on the planks of the scaffolding. Don't access scaffolding during inclement weather or when it's covered in ice or snow. This significantly increases the risk of slips, trips, or falling.13.14 Scaffold platforms. (1) The platform of each scaffold must. (a) be a minimum nominal width of 50 cm (20 in), except that a nominal 30 cm (12 in) wide work platform may be used with ladder jacks, pump jack or similar systems, (b) not leave more than one opening in the work platform, which must be no greater than 25 cm (10 in) in width, and. endurancenow.comshindo life wiki codescostco gas fairfield OSHA standard 1926.453 (b) (2) (v) requires workers to wear a body belt, with a lanyard attached to the boom or basket, when working from an aerial lift, including a scaffold. 2. Use of fall protection above 10 feet. According to OSHA standard 1926.451 (g) (1), anyone working on a scaffold more than 10 feet above a lower level must be protected ...10 ways to get your safety and health program started. 1. Establish safety and health as a core value. 2. lead by example. 3. implement a reporting system. 4. provide training. 5. conduct inspections. 6. Collect hazard control ideas. strong magnet remove security tag 1926.501 (b) (1) Unprotected sides and edges. Each employee on a walking/working surface (horizontal and vertical surface) with an unprotected side or edge which is 6 feet (1.8 m) or more above a lower level shall be protected from falling by the use of guardrail systems, safety net systems, or personal fall arrest systems. american hustle parents guideuscca appwww.usbankreliacard.com app download for android Employees performing work from a scaffold must be trained on proper use, maximum load capacity and any electrical hazards present. True ____________ scaffolds consist of one or more platforms supported by outrigger beams, brackets, poles, legs, uprights, posts, frames or similar rigid support.Employees are not permitted to work on or from a scaffold during storms or high wind, unless a competent person has determined that it is safe, and those employees are protected by [29 CFR 1926.451(f)(12)]: Personal fall arrest systems. Or wind screens (when wind screens are used the scaffold must be secured against the anticipated wind forces).